|

DIY 2×4 Porch Swing

Can a porch swing be made with just eight 2×4 pieces of lumber?  It sure can!

DIY 2x4 Porch Swing - Learn how to make a porch swing using just eight 2x4 pieces of lumber. Get the full tutorial at virginiasweetpea.com.

DIY 2×4 Porch Swing

I’ve been wanting a porch swing for our new patio at the lake

Update: See what the patio looks like now in this post.

Instead of buying a swing, Mr. SP and I challenged ourselves to build a swing using these plans from Jay’s Custom Creations.

DIY 2x4 Porch Swing - Learn how to make a porch swing using just eight 2x4 pieces of lumber. Get the full tutorial at virginiasweetpea.com.

Our DIY 2×4 Porch Swing has been in place for about a week and we have really enjoyed using it.  The swing is the perfect spot to sit and enjoy the lake view.

DIY 2x4 Porch Swing - Learn how to make a porch swing using just eight 2x4 pieces of lumber. Get the full tutorial at virginiasweetpea.com.

I added an outdoor rug from Walmart to soften the concrete and to add a pop of color to the porch.  The pillows on the swing are also from Walmart and they cost just $5 each. 

The plastic chairs are hand-me-downs that I spray painted turquoise.  We hope to soon build a few more wooden Adirondack chairs for this spot or maybe even an Adirondack chair bench.  (Our friend purchased this pattern and offered to let us borrow it.)

DIY 2x4 Porch Swing - Learn how to make a porch swing using just eight 2x4 pieces of lumber. Get the full tutorial at virginiasweetpea.com.

With the addition of the patio at the lake, we can now enjoy relaxing on the deck or on the patio.

DIY 2x4 Porch Swing - Learn how to make a porch swing using just eight 2x4 pieces of lumber. Get the full tutorial at virginiasweetpea.com.

The upper deck has four Adirondack chairs that Mr. SP made over the winter

Our new DIY 2×4 Porch Swing is definitely a great addition to our lake house.

Back of our house at Smith Mountain Lake showing our DIY Adirondack Chairs and our DIY 2x4 Porch Swing
DIY 2x4 Porch Swing - Learn how to make a porch swing using just eight 2x4 pieces of lumber. Get the full tutorial at virginiasweetpea.com.

How to Build a DIY 2×4 Porch Swing

We used this plan from Jay’s Custom Creations to make our swing.  I highly recommend watching Jay’s video before attempting this project.  Thanks for the plans and video, Jay!

This swing was made using eight 2×4’s.  You’ll also need deck screws, eye bolts, and chain to hang your swing.  As you read this post, you’ll see all of the equipment that we used to build our DIY 2×4 Porch Swing.

Step One – Cut the Arm Boards

The arms are constructed with two 2×4 boards.

The two boards for the arms were run through the planer on both sides to smooth them out and to remove the writing on them.

How to Make a DIY 2x4 Porch Swing - Get the step-by-step directions at virginiasweetpea.com.

The 2×4’s for the arm components need to be 3” in width for this project.  A 2×4 is 3 1/2” in width, so the table saw was used to rip 1/4” from each side.

How to Make a DIY 2x4 Porch Swing - Get the step-by-step directions at virginiasweetpea.com

Here the blade is set at 3 1/4 for the first cut.

How to Make a DIY 2x4 Porch Swing - Get the step-by-step directions at virginiasweetpea.com

And for the second cut to make the board 3” wide, the blade is set at 3”.

How to Make a DIY 2x4 Porch Swing - Get the step-by-step directions at virginiasweetpea.com

Now we have two 2×4’s that are 3” wide.  The strips to the right are what we cut off.  I don’t know what we will use them for, but I am saving them because they should be good for something.

How to Make a DIY 2x4 Porch Swing - Get the step-by-step directions at virginiasweetpea.com

Step Two – Cut the Arm and Back Support Pieces

All angles for the arm and back support pieces are 15 degrees.  The pieces were cut to length according to the cut sheet below.  (Get the cut sheet and directions at Jay’s Custom Creations.)

Cut List

Using the two 2×4 pieces that were cut to 3” width, the back supports and arm pieces were cut to the angle and widths as specified on the above cut sheet.  **Note that the lap joints shown on the cut sheet have not yet been made.**

How to Make a DIY 2x4 Porch Swing - Get the step-by-step directions at virginiasweetpea.com

Here the pieces are put together without the half lap joints.

How to Make a DIY 2x4 Porch Swing - Get the step-by-step directions at virginiasweetpea.com

The spots marked with an X will form the half lap joints.

How to Make a DIY 2x4 Porch Swing - Get the step-by-step directions at virginiasweetpea.com

Step Three – Make the Half Lap Joints

This step requires using a dado blade on the table saw. 

Mr. SP inherited a dado blade along with our 1950’s table saw from my grandfather but he had never used it.  The metal cover for the blade is only wide enough for one blade so we had to improvise and make a wooden one to use.  The blade depth was set to half the thickness of the planed 2×4 (for me, this was 11/16”).

These set up blocks from Woodpecker are handy to use when setting the blade depth on the saw.  Kreg also makes a similar set.  I highly recommend these!

How to Make a DIY 2x4 Porch Swing - Get the step-by-step directions at virginiasweetpea.com

A jig had to be constructed to cut the lap joints at 15 degrees.  Being married to an engineer has its advantages; Mr. SP designed and whipped this jig up in no time.  (Watching Jay’s video gives details on how to make this.)

How to Make a DIY 2x4 Porch Swing - Get the step-by-step directions at virginiasweetpea.com

I made a GIF showing Mr. SP making the half lap joints.  I was afraid of messing these up, so I let him do them all.

Use a dado blade to make a lap joint

Here you can see one of the half lap joints cut.  The area marked with the X is where the next half lap was cut.

How to Make a DIY 2x4 Porch Swing - Get the step-by-step directions at virginiasweetpea.com

The jig had to be adjusted to make the inside back support lap joint. 

You can see below where the cut will be made on the bottom board;  It will match up with the joint of the board I placed on top for demo.

How to Make a DIY 2x4 Porch Swing - Get the step-by-step directions at virginiasweetpea.com

The jig had to be adjusted again for the outside cut.  Make sure that your jig is in the proper place before cutting!

How to Make a DIY 2x4 Porch Swing - Get the step-by-step directions at virginiasweetpea.com

The pieces fit together almost perfectly.  Pretty amazing considering we were using a 60+ year-old saw and a make-it-yourself jig.

How to Make a DIY 2x4 Porch Swing - Get the step-by-step directions at virginiasweetpea.com

This view better shows how the half lap joint fit together.  Note that the two arms are mirror images of each other.

How to Make a DIY 2x4 Porch Swing - Get the step-by-step directions at virginiasweetpea.com

Step Four – Glue the Arm Pieces

It is critical that the two arm and back pieces have the same angle, so we glued them first. 

We clamped them together to keep the angle the same while the glue dried.  A workshop can never have enough clamps!

How to Make a DIY 2x4 Porch Swing - Get the step-by-step directions at virginiasweetpea.com

After the glue was dry, we glued and clamped the rest of the arm pieces.

How to Make a DIY 2x4 Porch Swing - Get the step-by-step directions at virginiasweetpea.com

Step Five – Plane the Arms

Our half lap joints were slightly proud (< 1/16″), so we ran the arms through the planer to make them smooth on both sides. 

We could have sanded both sides but using the planer was easier and saved time.

How to Make a DIY 2x4 Porch Swing - Get the step-by-step directions at virginiasweetpea.com

Step Six – Trim the Arms

A corner was cut off both arm assemblies per the instructions.

How to Make a DIY 2x4 Porch Swing - Get the step-by-step directions at virginiasweetpea.com

Step Seven – Sand the Arms

Use a belt sander to sand the edges of both arm assemblies.

How to Make a DIY 2x4 Porch Swing - Get the step-by-step directions at virginiasweetpea.com

Step Seven – Rout the Edges

Use a 3/8” roundover bit to rout the both the inside and outside edges of the arm assemblies – with the exception of the inside back and bottom edges.

How to Make a DIY 2x4 Porch Swing - Get the step-by-step directions at virginiasweetpea.com

Step Eight – Cut the Slats and Slat Supports

The remaining six 2×4’s were planed on both sides and then cut in half to form twelve 48” pieces.

How to Make a DIY 2x4 Porch Swing - Get the step-by-step directions at virginiasweetpea.com

Eleven of the 48” pieces form the slats for the seat and back and the remaining piece was ripped using the table saw to make two pieces of roughly 1-1/2” x 1-1/2”

How to Make a DIY 2x4 Porch Swing - Get the step-by-step directions at virginiasweetpea.com

The same 3/8” roundover bit was used to route the seat and back slats.

How to Make a DIY 2x4 Porch Swing - Get the step-by-step directions at virginiasweetpea.com

.

DIY-Porch-Swing-27

Step Nine – Add the Slat Supports

Cut the Slat Supports to the back and bottom lengths, then glue and screw into place.  (Use 2 inch exterior deck screws for this step.)

How to Make a DIY 2x4 Porch Swing - Get the step-by-step directions at virginiasweetpea.com

Step Ten – Install the Slats

The first slat to be installed is the front seat bench slat.  We used clamps and clamping squares to make sure that the swing would be square.  (Clamping squares are a super handy tool to have!)

How to Make a DIY 2x4 Porch Swing - Get the step-by-step directions at virginiasweetpea.com

Here is another view of the how the clamping square is used.

How to Make a DIY 2x4 Porch Swing - Get the step-by-step directions at virginiasweetpea.com

We pre-drilled and countersunk the holes so the screw heads would be flush with the board face.  

Screw the first board into place using 1-1/2” exterior screws, then lay out the other seat boards.  Use a woodworking rule to draw a line to use as a guide for screwing in the remaining screws.

How to Make a DIY 2x4 Porch Swing - Get the step-by-step directions at virginiasweetpea.com

The boards were spaced 1/8” apart.  Here you can see another handy use for a depth guide.How to Make a DIY 2x4 Porch Swing - Get the step-by-step directions at virginiasweetpea.com

Screw all of the seat slats into place, then follow the same procedure to screw the back slats into place.  Start with the top back slat.

How to Make a DIY 2x4 Porch Swing - Get the step-by-step directions at virginiasweetpea.com

Now the seat and back slats are in place.  Use a palm sander to remove the pencil marks from between the screws.

How to Make a DIY 2x4 Porch Swing - Get the step-by-step directions at virginiasweetpea.com

Step Eleven – Screw on the Eye Bolts

Four 3/8” x 6” eye bolts with nuts and four 3/8” galvanized washers are needed for this step.  (I’m not sure where the fourth eye bolt is in this picture!)How to Make a DIY 2x4 Porch Swing - Get the step-by-step directions at virginiasweetpea.com

Measure and mark where the hole is to be drilled.

How to Make a DIY 2x4 Porch Swing - Get the step-by-step directions at virginiasweetpea.com

Drill the hole and screw in the eye bolts.

How to Make a DIY 2x4 Porch Swing - Get the step-by-step directions at virginiasweetpea.com
How to Make a DIY 2x4 Porch Swing - Get the step-by-step directions at virginiasweetpea.com
How to Make a DIY 2x4 Porch Swing - Get the step-by-step directions at virginiasweetpea.com

Step Twelve – Hang the Swing

Since the swing that we built was 53″ (center-center of the eye bolts), and our deck joists were 12″ center-center, we had to improvise a solution.  We added these 2″x 8″ boards between the existing deck floor joists using these joist hangers.  This made centering the swing under the deck easy.

We purchased a porch swing chain set from the local hardware store.  It came with all the necessary hardware to finish the project as shown with the exception of the four zinc-coated quick links that connect the chair’s eye bolts to the chain.

How to Make a DIY 2x4 Porch Swing - Get the step-by-step directions at virginiasweetpea.com

Here you can better see how our swing hangs from the ceiling.

How to Make a DIY 2x4 Porch Swing - Get the step-by-step directions at virginiasweetpea.com

Enjoy Using the DIY 2×4 Swing

We are 100% pleased with the end result of this project and anticipate many pleasant hours spent swinging on our porch.

How to Make a DIY 2x4 Porch Swing - Get the step-by-step directions at virginiasweetpea.com
How to Make a DIY 2x4 Porch Swing - Get the step-by-step directions at virginiasweetpea.com
How to Make a DIY 2x4 Porch Swing - Get the step-by-step directions at virginiasweetpea.com

Our View from the Swing

We have a beautiful view from our DIY 2×4 Porch Swing and are sure to enjoy using it in all seasons.

Our View at Smith Mountain Lake

Click here to see more outdoor projects at our lake house and to tour the inside of our home.

Our View at Smith Mountain Lake

If you like this project, pin it so that you don’t forget it.  Pinning also helps others to discover it on Pinterest.

DIY 2x4 Porch Swing - Learn how to make a porch swing using just eight 2x4 pieces of lumber. Get the full tutorial at virginiasweetpea.com.

What’s next at the lake?  We’ve been working on the landscape and have purchased hoses for both the back and side faucets.  Hose hangers are next on our DIY woodworking project list.

We love our Smith Mountain Lake house.  You can see all of our lake house projects here.

Favorite Projects

If you liked this post, check out more popular projects.

43 Comments

    1. I’ve never had a spot to hang one until now. I’m looking forward to swinging in it this weekend.

  1. I have been wanting to make a porch swing! Thank you for the tutorial……definitely pinned this one! I am so happy I found your site through the linky party. Nice to find other woodworking sites:)

    1. Thank you! This was one of the more complicated projects that we’ve completed. We are so happy with the end result!

  2. Great job on the swing! I love how you can face the lake. Your porch would be my favorite place.

    1. Thank you! I can’t wait to get to the lake for the weekend. I’ve had a hurt back for over a week and am not sure that it will allow me to swing, but I can certainly sit and enjoy our view.

  3. Pingback: Talk of the Town #81 - My Repurposed Lifeâ„¢
  4. Girl, you never cease to amaze me. What a gorgeous swing you’ve built here–and you have the PERFECT spot for it there at SML! I LOVE this, and your instructions make me think that I could build one myself. Thanks for writing those out so carefully.

    And thanks for joining the Grace at Home party. I’m featuring you this week!

  5. Pingback: Inspiration Monday Party - Inspiration For Moms
  6. What a gorgeous well designed swing. Its wonderful. You obviously took alot of effort to provide a very good tutorial as well.

    A beautiful swing for a beautiful setting. Thanks for sharing. Pinning.

  7. love…love! This is an awesome swing Paula! Especially with your fabulous views my friend! I have no doubt you’ll enjoy many evenings here with a cool drink swinging and watching the sunset.

  8. Pingback: 12 Porch Swing Ideas That Will Help You Get The Kids Outside - Common Cents Mom
  9. Pingback: Woodworking Guide Pdf – Legal Esclarin
  10. Hello, awesome swing and great view! I will like to know the measurements of the links? And what is the black thing on the links that are in the ceiling? Does that comes with the links? Ty!

    1. Thank you! To hang the swing, We purchased a porch swing chain set from the local hardware store.  It came with all the necessary hardware to finish the project with the exception of the four zinc coated quick links that connect the chair’s eye bolts to the chain.

      Paula

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.